BMR Suspension Lowering Springs (SP083R)

Fits 2015-2023 S550 Mustangs (Non-Magneride);Fits 2024-Current S650 Mustangs (Non-Magneride);Lowers your Mustang for an aggressive look;Greatly improves handling;246 lb/in front linear rate;980 lb/in rear linear rate;Manufactured from chrome silicon high-tensile spring wire;Cold wound on a CNC coiling machine to exact specifications;Lifetime warranty against spring sag;Stress-relieved at 750 degrees Fahrenheit;Shot-peened;Computer tested for accurate height and spring rate;Available in red for long lasting good looks;3-4 hour installation time;Proudly designed in the USA!;Proudly made in the USA!. BMR has designed the SP083 for the handling crowd who want to use their cars for road course and autocross..
There is nothing like the aggressive look of a car with the right stance! Over time, stock springs sag, get rusty, and simply wear out. BMR Suspension believes the right springs go beyond looks?your 2015-2023 S550 Mustang and 2024 S650 Mustang needs to perform, too! All BMR springs are manufactured from chrome silicon high-tensile spring wire, and are cold wound on a CNC coiling machine. The CNC coiling head can adjust the spring diameter in real time to ensure that every spring is exactly the same. This guarantees that your right spring matches your left spring. Every BMR spring is compressed solid at the factory, not once, but twice. This gives the spring its permanent set, and guarantees no sag. BMR springs are stress-relieved at 750 degrees F, ensuring most stresses induced during the winding process are eliminated. All springs are then shot-peened to eliminate residual surface stresses. Many spring manufacturers skip this step, but BMR insists on this operation as part of our spring manufacturing process. Every spring is computer tested as the last step?every spring, not just a sample from each batch. Each spring is loaded in the spring tester at the factory, then compressed and the CNC load cell measures the force for a variety of spring lengths. This allows BMR to offer a LIFETIME WARRANTY against spring sag. Blending aesthetics and performance, BMR has designed the SP083 for the handling crowd who want to use their cars for road course and autocross. These springs will lower your S550 and S650, and feature a fine-tuned spring rate to give you the ultimate in handling. The linear spring rate (246 lb/in front, 980 lb/in rear) offers plenty of support, keeping the body flat and level in the corners. When performance and looks are a must, rely on BMR Suspension! BMR Suspensions SP083 lowering springs are available in red powdercoat for long-lasting good looks. Installation time is about 3-4 hours. Proudly made in the U.S.A.

There is nothing like the aggressive look of a car with the right stance! Over time, stock springs sag, get rusty, and simply wear out. BMR Suspension believes the right springs go beyond looks?your 2015-2023 S550 Mustang and 2024 S650 Mustang needs to perform, too! All BMR springs are manufactured from chrome silicon high-tensile spring wire, and are cold wound on a CNC coiling machine. The CNC coiling head can adjust the spring diameter in real time to ensure that every spring is exactly the same. This guarantees that your right spring matches your left spring. Every BMR spring is compressed solid at the factory, not once, but twice. This gives the spring its permanent set, and guarantees no sag. BMR springs are stress-relieved at 750 degrees F, ensuring most stresses induced during the winding process are eliminated. All springs are then shot-peened to eliminate residual surface stresses. Many spring manufacturers skip this step, but BMR insists on this operation as part of our spring manufacturing process. Every spring is computer tested as the last step?every spring, not just a sample from each batch. Each spring is loaded in the spring tester at the factory, then compressed and the CNC load cell measures the force for a variety of spring lengths. This allows BMR to offer a LIFETIME WARRANTY against spring sag. Blending aesthetics and performance, BMR has designed the SP083 for the handling crowd who want to use their cars for road course and autocross. These springs will lower your S550 and S650, and feature a fine-tuned spring rate to give you the ultimate in handling. The linear spring rate (246 lb/in front, 980 lb/in rear) offers plenty of support, keeping the body flat and level in the corners. When performance and looks are a must, rely on BMR Suspension! BMR Suspensions SP083 lowering springs are available in red powdercoat for long-lasting good looks. Installation time is about 3-4 hours. Proudly made in the U.S.A.